Parker Manifold Simplifies Sensor Installation

Parker Hannifin has created a highly integrated manifold concept that is said to offer users a simpler means of installing level-measurement instrumentation to process tanks and vessels. Two single-piece manifolds integrate all of the valves and features required for connecting the upper and lower pressure-sensing points to a differential pressure transmitter. The approach is said to eliminate a large amount of weight, size and potential leak paths compared with conventional 'hook-ups' that are fabricated using discrete valves and tubing connections.

Called CCIMS Level-Flange, the solution consists of two manifolds. One provides a single-piece solution for the lower or 'wet leg' pressure connection at the bottom of a tank. This has a flange at one side for connection to the tank, double block-and-bleed valves in a monoflange style, a mounting point for a differential process transmitter and tube connections for the balance-line connection to the second sensing point. The second manifold provides an integrated solution for the upper or 'dry leg' pressure-sensing point, with a flange connection, block-and-bleed valves and balance-line connections.

The intimate nature of the piping connection provided by CCIMS Level-Flange aids the fundamental performance of the instrument system. Traditional hook-ups, fabricated from discrete valve and tubing components, typically involve longer flow paths, bends and sometimes changes in bore size. These can introduce pressure drops that can decrease measurement accuracy, commonly referred to as 'gauge-line error'. CCIMS Level-Flange provides a short, straight and even flow connection - allowing end users to benefit fully from the instrument's accuracy to monitor process levels.

The close-coupled design ensures that the differential pressure instrument is mounted directly adjacent to the process vessel - helping to avoid the common problem of blockages that can be caused by factors such as viscous media, hydrate formation and freezing. The weight and size of the integrated manifolds is also reduced compared with other solutions. A complete assembly with instrument only extends around 10.4in/26.3cm from the tank - which can be as little as a half that of some other hook-ups.

This eliminates any need for supporting metalwork and reduces the likelihood of clashing with any nearby pipework. The integrated nature of the manifolds also means that numerous joints are eliminated, helping to avoid the safety issues caused by leakages or emissions. CCIMS Level-Flange is expected to reduce the installation time and cost of differential pressure transmitter level-measurement systems by up to 85 per cent.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more