Bluetooth Smart Modules from TAIYO YUDEN are ideal for applications that require wireless communication with low-energy consumption

Bluetooth® Smart Modules from TAIYO YUDEN are ideal for applications that require wireless communication with low-energy consumption. The EYSGCN series, EYSGJN series, and EYAGJN series Bluetooth Smart Modules with Nordic nRF51822 or nRF51422 are cost effective modules with integrated high performance antennas. The EYSGCN series' small outline of 9.6 x 12.9 x 2.0 mm and the EYSGJN and EYAGJN series’ ultra-small footprint of 5.1 x 11.3 x 1.3 mm make them suitable for wearable devices, healthcare devices, home automation, and other applications. All Bluetooth Smart Modules from TAIYO YUDEN are FCC/IC/Japan certified, cost-effective, and are a faster time-to-market solution.

Specifications    
  •     Frequency: 2402 to 2480 MHz
  •     Output power: +4 dBm typ.
  •     Single power supply: 1.8 to 3.6 V
  •     ARM® Cortex®-M0 32-bit processor and 256 KB Flash and 32 KB RAM
  •     FCC/IC/Japan qualified
  •     RoHS-compliant and lead free
  •     Interface: SPI, UART, I²C, and 8/9/10-bit ADC
  •     Operating temperature -20° to 75°C
Applications
  •     Health check monitors
  •     Car electronics
  •     Smart meters
  •     Home security and sensors
  •     Home automation
  •     Cameras
  •     Wearable devices
  •     Computer peripherals

EYSGCNZWY Features         
  •     Bluetooth 4.2 low energy
  •     Single-mode Bluetooth Smart slave/master
  •     Integrated system/sleep clock
  •     Integrated high performance ceramic chip antenna
  •     FCC/IC/Japan qualified
  •     Nordic nRF51822
  •     Outline: 9.6 x 12.9 x 2.0 mm with 1 mm pad pitch

EYSGJNZWY Features
  •     Bluetooth 4.2 low energy
  •     Single-mode Bluetooth Smart slave/master
  •     Integrated system clock
  •     Integrated high performance pattern antenna
  •     FCC/IC/Japan qualified
  •     Nordic nRF51822
  •     Outline: 5.1 x 11.3 x 1.3 mm max

EYAGJNZXX Features
  •     ANT™ + Bluetooth 4.2 low energy
  •     ANT + Single-mode Bluetooth Smart slave
  •     Integrated system clock
  •     Integrated high performance pattern antenna
  •     FCC/IC/Japan qualified
  •     Nordic nRF51422
  •     Outline: 5.1 x 11.3 x 1.3 mm max

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more