i.MX 6UltraLite Applications Processors

Expanding the i.MX 6 series, Freescale's i.MX 6UltraLite is a high performance, ultra-efficient processor family featuring an advanced implementation of a single ARM Cortex-A7 core, which operates at speeds up to 528 MHz. The i.MX 6UltraLite applications processor includes an integrated power management module that reduces the complexity of external power supply and simplifies power sequencing. Each processor in this family provides various memory interfaces, including 16-bit LPDDR2, DDR3, DDR3L, raw and managed NAND Flash, NOR Flash, eMMC, Quad SPI, and a wide range of other interfaces for connecting peripherals such as WLAN, Bluetooth™, GPS, displays, and camera sensors. The i.MX 6UltraLite can be powered by a discrete power circuit.

Features
  •     ARM Cortex-A7 at up to 528 MHz
  •     An advanced power management architecture featuring multiple energy saving modes, dynamic voltage and frequency scaling, as well as integrated power switch for flexible power gating in low-power modes
  •     Flexible boot options, including support for Quad SPI and raw NAND
  •     A memory controller that interfaces to both DDR3/DDR3L and LPDDR2
  •     Robust security features such as secure boot, hardware cryptographic cipher engines and random number generators help enable hardware-verified peripheral and memory access requests for secure isolation and prevention of tainted system resources
  •     Hardware tamper detection and an integrated on-the-fly DRAM encryption/decryption engine make the i.MX 6UltraLite among the most secure ARM Cortex-A7 microprocessor solutions available
  •     Processor supports a variety of interfaces: two high-speed USB OTG with PHY, multiple expansion card ports (high-speed MMC/SDIO host and other), two 12-bit ADC modules with up to 10 total input channels, two CAN ports, two smart card interfaces compatible with EMV Standard v4.3, and a variety of other popular interfaces (such as UART, I²C, and I²S serial audio)
  •     Two package offerings: 14 x 14 0.8 mm pitch for ease of design and 9 x 9 0.5 mm pitch for space constrained applications.
  •     Common IP with i.MX6 for easy migration

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more