Cree XTE-HV Series on Marktech Evaluation Boards

Optimized for non-directional and small LED replacement lamps such as B10 candelabra, E17, GU10 and A19 bulbs, the XLamp XTE High-Voltage White LED delivers both high lumen output and high efficacy in a small footprint.

"Relentless innovation, like the SC3 Technology Platform, will always be part of Cree's DNA, and applying the innovations to optimize application performance, lower system cost and drive LED lighting adoption is our mission," said Mike Watson, Cree senior marketing director, LED components. "Leveraging the power of the SC3 Technology Platform, Cree has fundamentally transformed price-performance with the XB-D LED, set new performance standards with the XT-E LED and with the introduction of the new XT-E and XM-L High-Voltage LEDs, redefined performance limits for LEDs of this size." The XT-E High-Voltage LEDs can deliver up to 357 lumens at 3 watts in cool white (6500K) and up to 275 lumens at 3 watts in warm white (3000K), both at 85 degrees C. The XM-L High-Voltage LEDs can deliver up to 647 lumens at 6 watts in cool white (6500K) and 555 lumens at 6 watts in warm white (3000K) both at 85 degrees C.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more