Development of the "HW Series" of Low Impedance, Long Life Aluminum Capacitors

Nichicon Corporation has developed the HW series of radial leaded type, low impedance, long life aluminum capacitors perfectly suited to withstand high ripple current and long life demands of power sources. The line-up will be on show at the CEATEC JAPAN 2012 exhibition to be held at Makuhari Messe from 2–6 October (Tues-Sat).

As electronic appliances and AC adaptors are reduced in size, the manufacturers of these devices are making their warranties longer with each passing year. This trend is accelerating and energy efficiency is another keyword. Amid this market context, demand is on the rise for low impedance, long life aluminum capacitors for use as secondary power circuits.

To meet these market needs, Nichicon has developed the HW series line-up of radial lead type low impedance, long life aluminum capacitors.

Based on technology developed by Nichicon, this product applies a new electrolyte solution and assembles optimal components to achieve a long life guarantee of 10,000 hours, approximately 1.7 times longer than the current low impedance HV series product (guaranteeing 6,000 hours).

In addition, the HW series has a wider rated voltage range than the HV series, which is designed to suit diverse circuit voltages, and it will contribute to the better endurance of all kinds of power sources, especially batteries for electric appliances and AC adaptors.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

Model QLS Quad Loop Splitter Splits One 4-20 mA Current Loop into 4 Independent Loops

Image
Model QLS Quad Output Loop Splitter / Retransmittersources up to four (4) independently adjustable 4-20 mA outputs from a single input, which can be 4-20 mA, 1-5V, 0-5V or 0-10V, as selected by jumpers. The outputs can share a common ground. The input and outputs are mutually isolated to ±10V by means of active circuitry to accommodate differences in local grounds with normal industrial grounding practices. If any device in an output loop is removed from a loop or fails, or if a wiring fault occurs, the other loops continue to operate properly. Each loop only drives a single load, avoiding compliance problems. Model QLS overcomes problems associated with the common industrial wiring practice where the same 4-20 mA signal from a transmitter is sent to multiple devices in series. In such a circuit, the devices in the loop cannot share a common ground, but must be electrically floating, which is often not possible. When any device in the loop is removed, fails or if a wiring fault occur
Read more