Eaton Signs Letter of Intent with COMAC to Supply Cargo-Door Actuation System for C919 Aircraft Program

Diversified industrial manufacturer Eaton Corporation has signed a letter of intent with Commercial Aircraft Corporation of China, Ltd. (COMAC) to supply the cargo door actuation system for the COMAC C919 program. The system’s lightweight design helps reduce overall aircraft weight and improve fuel efficiency. The value of the contract has not been disclosed.

“Our selection by COMAC was based on Eaton’s superior system design and integration capabilities, which optimize aircraft performance and lifecycle cost,” said Joe-Tao Zhou, president – Asia Pacific, Eaton’s Aerospace Group. “Eaton’s innovative solutions are driving growth in China’s emerging aerospace market and extending Eaton’s broad product portfolio to new markets worldwide.”

Eaton’s cargo door actuation system will lift the fore and aft cargo doors on the C919 passenger jet. The cargo door actuator contains integrated control electronics, a design innovation that eliminates the need for a separate controller. Eaton’s integrated approach saves weight and volume, leading to overall aircraft weight reductions, improved fuel efficiency and lower environmental emissions.

In the aerospace industry, Eaton is a leading supplier of hydraulic, electro-hydraulic pump and generator products and integrated systems; engine and airframe fuel pumps; electric motors; aircraft door actuation, flight and flow controls; fluid, fuel and air delivery products and systems; nose wheel steering systems; integrated control systems; cockpit controls and displays; power and load management systems; pressure sensors, seals, and fluid health monitoring products and systems. Eaton serves commercial and military aviation, aerospace, military weapons, marine and off-road markets worldwide.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more