Rapid Cure Floor Coating for UK's 3rd Airport

British Airports Authority (BAA) and architects Foster and Partners specified Ronacrete’s Ronadeck Fast Grip to provide an attractive, slip resistant surface over original granite and marble slabs.

The slabs which form the passenger walkways to and from the airport concourse, check-in areas, car and bus parks and train terminal were coated shortly after construction with a non-slip coating. These needed re-coating after millions of pairs of feet had worn the coating smooth.

The existing coating was ground down to expose the original marble paving, and Ronadeck Fast Grip then applied.

BAA’s criteria for the new slip-resistant coating included aesthetics, slip resistance, fast curing for speed of recommissioning and optimum safety during application. BAA commissioned HSE laboratories to test Ronadeck Fast Grip to measure anti-slip performance. Subsequently 2,500m2 were laid.

A special water based clear surface sealer was applied to aid retention of the hardwearing aggregate and make the surface easier to clean of chewing gum and liquid spillages.

31,000 people use the terminal at any one time and it was vital that the installation caused minimum disruption and allowed freedom of access during that period.

Ronadeck Fast Grip was applied at night and was cured and ready for traffic by the time the airport opened for business the following morning.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more