The new Bürkert TwinPower Technology

Our revolutionary TwinPower technology uses two coils. Therefore our solenoid valves are 50% smaller than standard valves with same performance. More minimum for your great ideas.

Our new TwinPower technology operates with two coils instead of only one as before. This means greater freedom when it comes to energy efficiency, miniaturisation and performance: our TwinPower solenoid valves take up 50% less installation space whilst offering the same fluid switching capacity, which makes them the best performing valves on the market in their class. The new dual-coil concept also permits electrical power consumption to be reduced by 75%.

The new TwinPower solenoid valves 6624/6626 rely on the tried-and-tested, reliable and globally successful rocker principle with separation of media. The innovation in the type 6624/6626 TwinPower concerns the TwinPower actuators with two solenoid coils which make it possible to build a significantly smaller valve. The principle remains the same - but with significant advantages such as optimised cleanability and a significantly reduced heat transfer into the medium. Further information on our new TwinPower solenoid valves:
  • Solenoid valve type 6624
  • Solenoid valve type 6626: further information is available shortly
Our new TwinPower technology means that your system has an even brighter future. The dimensions of our solenoid valves have been reduced significantly, by up to 50%, which adds up to:
  • a system that takes up less space,
  • less use of material for the manifolds
  • and a reduced internal volume of the overall system.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more