Plastic Bushing Made of Renewable Materials

igus® has developed a new ecological plastic bushing made of 54 percent raw, renewable materials. iglide® N54 plastic bushings use vegetable oil rather than the more traditionally used crude oil. They are ideal for low-load applications in a variety of different industries such as consumer products, general mechanical engineering and furniture. “The new, self-lubricating iglide N54 material is the first step towards developing an environmentally friendly, or “green”, plastic bushing,” explains Tom Miller, Bearings Unit Manager for igus.

iglide N54 fits seamlessly with igus’ commitment to developing environmentally friendly plastic bushings to replace metal or bronze bearings that require messy lubrication. In comparison, every iglide plastic bushing uses solid lubricants embedded inside millions of tiny chambers that cannot be pressed out. This means the bushings do not require any oil or grease and so no contaminants are released into the environment. In addition, an iglide plastic bushing is lighter than its metal counterpart, which leads to reduced energy consumption.

Furthermore, less energy is required for the production of plastics compared to metals. For example, the energy from four gallons of crude oil is necessary to produce four cups of aluminum, and the energy from three gallons of crude oil is necessary to produce four cups of steel. In comparison, it only takes 0.48 gallons of crude oil to create four cups of plastic and igus expects this value to fall even further based on continued breakthroughs in the field of vegetable-oil-based plastics.

According to the European Bioplastics Association, which serves as both a contact platform and catalyst for advancing the aims of this growing industry, the global production capacity for bioplastics will more than double from 2010 to 2015.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more