EVERLIGHT Electronics Announces New COB Ju LED Series

Adding to the performance and popularity of EVERLIGHT’s 6.4W and 8W Chip-on-Board (COB) LED series, one of the highest CRI and highest efficiency COBs on the market, EVERLIGHT ELECTRONICS CO. LTD. (TSE:2393) announces the brand new and smaller COB Ju LED series which is perfectly suitable for directional and decorative applications such as MR lamps and P35 bulbs in the Light Fair International USA 2012.

For these types of applications, an LED light source must exhibit compact size, high efficiency, sufficient lumen output, high CRI, high color uniformity, and proper light distribution to maintain a comfortable and uniform lighting environment – all at consumer acceptable prices. With its new COB Ju Series, EVERLIGHT ELECTRONICS has created the other ideal LED to address major challenges posed when designing a retrofit like MR, GU or candelabra type: minimum efficiency requirements, thermal management in limited space, and complexity of design.

EVERLIGHT’s COB series is a 3.7W multi chip, ceramic substrate based LED that boasts a low thermal resistance (Rth <1.8°C/W) and superior efficacy of 100lm/W at 3000K CCT and high CRI (>80Ra). It will be available not only in ANSI 3000K CCT but in all Energy Star / ANSI color temperature ranges. Mechanically, the COB Ju series can be mounted directly on heat sink eliminating the SMT process. This provides more direct thermal dissipation, ease of assembly, and lowering of the system cost in lighting applications.

EVERLIGHT COB Ju Series is using the standard DC chips configured in series and parallel to provide the most convenient driving conditions for existing driver designs. Also, with a ceramic substrate, users can have higher reliability and better thermal dissipation. The COB Ju Series also can achieve the low cost of industry target, >400lm/$ for a COB LED light source. This is a superb single emission area COB LED that needs to be used.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more