TI introduces smallest 2.5-A power module with 65-V transient protection

Texas Instruments Incorporated (TI) (NASDAQ: TXN) today introduced a new power module with 65-V transient protection that integrates a DC/DC converter, inductor and passives in a very small, easy-to-use package. The 2.5-A TPS84250 meets the EN55022 Class B electromagnetic emissions standard and features frequency synchronization to cleanly power noise-sensitive analog circuits in test and measurement, industrial motor control, medical and imaging applications. For more information and samples, visit www.ti.com/tps84250-pr.

The TPS84250 step-down power module supports input voltages from 7 V to 50 V and provides a positive output voltage from 2.5 V to 15 V in a small, thin 9-mm by 11-mm package. Watch a video at www.ti.com/tps84250-prv.

For applications that require a negative output voltage, TI offers the TPS84259 4.5-V to 40-V input, up to 15-W power module with frequency synchronization and low electromagnetic interference (EMI). This new power module provides output voltage down to -17 V for powering sensors, bipolar amplifiers, split-rail data converters and other analog circuits. For clean, low-noise voltage rails, the TPS84250 and TPS84259 modules can be paired with wide-input voltage linear regulators such as the 1-A, 36-V TPS7A4700 and 1-A, -36-V TPS7A3301.

The TPS84250 and TPS84259 join TI's TPS84k power module family, which also provide power for DSPs and FPGAs that require lower input voltages. For more information on all of TI's TPS84k integrated power modules, visit www.ti.com/tps84k-pr. TI offers a variety of tools and support to speed design, including circuit topology calculators for the TPS84250 and TPS84259.

Key features and benefits of the TPS84250 and TPS84259 power modules
  •     65-V transient protection eliminates additional system protection components.
  •     Frequency synchronization reduces noise.
  •     Compliant to EN55022 Class B electromagnetic emissions standard for low EMI noise.
  •     Very small, low-profile 9-mm by 11-mm by 2.8-mm QFN package is 75-percent smaller in area than open-frame power modules.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more