CUI Introduces 10~30 W Chassis Mount Dc-Dc Converters

CUI Inc announced the release of a new line of 4:1 input Dc-Dc converters ranging from 10~30 W that are housed in a compact chassis mount package. Featuring screw terminal connections, the VYB10W-T, VYB15W-T, VYB20W-T and VYC30W-T Series are designed for applications where the convenience of chassis mounting is required, including transportation equipment, mobile equipment, and telecom base stations. With a temperature range of -40 to + 85°C, the converters are ideally suited for most operating environments.

Available in +3.3, +5, +12, or +15 Vdc single output models and ±12 or ±15 Vdc dual output models, the converters accept input voltages of 9-36 Vdc or 18-75 Vdc. The wide input range is very useful when being driven from a fluctuating device such as a battery which can see both charging and discharging conditions. All outputs are fully regulated to within ±0.5% over all line input conditions and ±1.0% for all load conditions. Additionally, input to output isolation of 1,500 V dc is provided across the range. Dimensions for the VYB10W-T, VYB15W-T, and VYB20W-T Series are 55 x 35 x 19 mm while the VYC30-T Series measures 67.5 x 55 x 19.1 mm.

Single output 15 W, 20 W and 30 W models offer an output trim that allows adjustment within ±10% of nominal output, while all models include remote on/off. Additional features include short circuit protection for the entire series, and over current and over voltage protections for 15 W, 20 W and 30 W models. An optional accessory kit is also available for DIN rail mounting.

The VYB10W-T, VYB15W-T, VYB20W-T and VYC30W-T Series are available through Digi-Key starting at $29.49 for 100 pieces for 10 W models. Contact CUI directly for OEM pricing.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more