FLOOR PATCH™ - PATCHING COMPOUNDS HAVE 3 TIMES MORE STRENGTH THAN CONCRETE

Floor Savers™ floor maintenance and repair products from Devcon are all-purpose concrete patching compounds that can be easily applied by plant maintenance personnel. With excellent adhesion to a variety of substrates, they cure at room temperature and achieve compressive strengths of 8000-9000 psi, over three times the typical strength of concrete. Easily trowelable to a nonporous finish, these durable compounds provide excellent resistance to water, oils, solvents, and alkalis and are acceptable for use in meat and poultry plants. Their nonsagging formulation will not run or drip when used on vertical or overhead applications.

Floor Patch™ is a general-purpose concrete patching compound that provides excellent adhesion to concrete, brick, masonry, metal, or wood surfaces. It can be easily mixed and trowel-applied, curing at room temperature to a hard concrete surface in 8 hours.

Floor Patch FC is a fast-curing version of Floor Patch, ideal for quick, efficient floor repairs in high-traffic areas. It has a 15-minute pot life and cures completely in 3 hours. With Devcon Concrete Primer, Floor Patch FC bonds to wet surfaces and at temperatures below 40° F, allowing fast, effective floor repairs in all environments.

For industrial floors exposed to harsh chemicals, Ultra Quartz™ is a heavy-duty, premium floor patching system with excellent chemical resistance. It offers outstanding protection against acids, alkalis, water, oils, solvents, and most chemicals. This high-performance patching system includes a surface primer for superior bonding to existing concrete or other surfaces.

Devcon Floor Savers floor maintenance products are 100% solids formulations that meet federal VOC regulations. Floor Patch is available in 10-pound and 40-pound containers, Floor Patch FC in a 10-pound container, and Ultra Quartz in a 35-pound container. At a thickness of ¼", Floor Patch covers 18 square feet per 40-pound container, Floor Patch FC covers 4.5 square feet per 10-pound container, and Ultra Quartz covers 13 square feet per 35-pound container.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more