Infrared Thermometer Combines Minimised Electronic with Innovative LED Display

Optris GmbH introduces the new optris CSmicro series from which especially OEM customers will benefit according to the great product potential of these infrared thermometers. The improved price-performance-ratio supports the integration of the devices within OEM solutions and the simultaneous operation of the measurement devices at several infrared measuring points.

The usage of the compact pyrometers within the automotive area is versatile.  The infrared thermometers can be included within e.g. mobile paint dryers for temperature control or during laminating and welding process of plastic parts to ensure a constant process and quality monitoring.

The innovative temperature sensors cover a temperature range from -40°C to 1600°C and are available with the new, innovative LED display. The display at the seperate electronic serves as a target help for the sensor adjustment as well as to show the condition of the pyrometer (e.g. overheating of the sensor). Additionally, a visual alarm can take place parallel to the new alarm output at the device (open collector). A temperature code indication completes the innovative concept.

The electronic is located within the cable of all infrared thermometers of the new optris CSmicro series. The electronic consists of a size of only 31x12 mm and was reduced by 25%. Moreover, Optris sets new benchmarks regarding the size and robustness of the sensing heads within the area of industrial infrared thermometers. The miniaturized sensing heads are developed for the use in cramped and small surroundings. The robust, superior design allows the operation with temperatures up to 180°C without cooling. This benefit accounts to a reduction of cost for mechanical installations.

The pyrometer of the optris CSmicro series offer additionally to the in industry widely used analog two-wire interface (4-20 mA current loop) the possibility of sending digital data via an USB interface to a connected PC. Beside a temperature recording via the integration of this sensor into the optris CompactConnect software a complete programming and remote setup can be done.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more