Aaxeon Releases New 10/100/1000BaseT to 1000BaseSX/LX Converters

Aaxeon Technologies is proud to announce the release of our new FCU-280x Series of 10/100/1000BaseT to 1000BaseSX/LX Gigabit Fiber Media Converters.  Aaxeon’s Gigabit media converter series FCU-280x (FCU-2802SC, FCU-2802SC-S10, and FCU-2805SFP) supports conversion between 10/100/1000Base-T and 1000Base-LX/SX networks. With three types of connectors, SC, SFP, and WDM, single-mode or multi-mode media can be provided by the FCU-280x series for efficient Gigabit fiber network construction. The Ethernet signal allows the connectors to link up easily, efficiently and inexpensively.

The FCU-280x series can be used as a standalone unit when powered by it's DC adapter or used as a slide-in module to Aaxeon’s 19-inch 16-Slot media converter rack chassis. These media chassis can supply power to the FCU-280x and permit the fiber-optic network to be maintained at one location. Since the FCU-280x series fully complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T and IEEE 802.3z 1000Base-LX/SX, the installation of this Gigabit media converter is quick and easy using a simple plug and play feature. The FCU-280x series also supports flow control and back pressure in half-duplex to eliminate the chance of packets loss.

Features include:
  • Complies with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/LX
  • TP port supports 10/100/1000Base-T auto-negotiation and auto-MDI/MDI-X
  • Layer 2 key features:
    • IEEE 802.3x Full-Duplex Flow-Control and Back-Pressure in Half-Duplex eliminate the chance of packets loss
    • Supports auto MDI/MDI-X function
    • Store-and-Forward mechanism
    • Non-blocking full wire-speed forwarding rate
  •     Media conversion between 10/100/1000Base-T and 1000Base-SX/LX
  •     Fiber media allows both multi-mode fiber and single-mode fiber use SC/ LC/ WDM connectors
  •     Wall-Mountable design
  •     LED indicators for network diagnose easily
  •     Provides DIP switch for LFP function (Disable / Enable) setting
  •     Choices of fiber connector from SC, LC and WDM, multi-mode / single-mode fiber for 1000Base SFP interface
  •     2-Year Warranty

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more