Aaxeon Releases New 26-Port PoE Managed Industrial Switch

Aaxeon Technologies is proud to announce the release of our new LNP-2602GN 26-Port PoE (Power over Ethernet) Managed Industrial Rack Mount Ethernet Switch.  The new LNP-2602GN features 24 x 10/100BaseTX power and 2 x 10/100/1000T/Mini-GBIC Combo ports with all 24 10/100BaseTX ports capable of providing Power over Ethernet (PoE).  Along with the standard model, the LNP-2602GN is also available in an extended operating temperature model (LNP-2602GN-T) that can withstand temperatures of -35° C to 70° C.

The LNP-2602GN allows users up to 24 PoE ports for applications needing numerous PoE connections like multiple IP surveillance cameras.  Along with providing a high port count, the LNP-2602GN also boasts many other important features like LLDP (Link Layer Discovery Protocol), which allows the switch to advise its identification & capability on the LAN, and security features like IEEE 802.1x RADIUS, to remotely authenticate users.  The LNP-2602GN also supports Ethernet Ring Redundancy (Recovery time < 300ms) along with IEEE 802.1d Spanning Tree and IEEE 802.1w Rapid Spanning Tree to make sure that critical data is never interrupted.

The LNP-2602GN is a very flexible switch which can be managed multiple ways, including SNMP, Web-based interface, Telnet, and CLI management.  The new LNP-2602GN is one of the most cost effective solutions for applications that need multiple PoE ports in the market today.

Key Features:
  • 24-port 10/100TX + 2-port 10/100/1000/Mini-GBIC Combo
  • Embedded 24-Port PoE Injector Function
  • Back-plane (Switching Fabric): 8.8 Gbps
  • 4Mbits Packet Buffer
  • 8K MAC Address Table
  • Port Based VLAN and 802.1 Q Tag VLAN
  • Port Trunk with LACP
  • QoS (Quality of Service)
  • Port Mirroring: Monitor traffic in switched networks
  • Port Security and IP Security
  • IEEE 802.1p Class of Service
  • IEEE 802.1d Spanning Tree and IEEE 802.1w Rapid Spanning Tree
  • IEEE 802.1x / RADIUS
  • IGMP Snooping
  • Redundant Ring function (Recovery Time < 300 ms)
  • SNMP Trap
  • Redundant Power Supply Design

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more