DNA-DIO-452 12-Channel Electromechanical Relay Output Layer

The DNA/DNR-DIO-452 are 12-channel, electromechanical relay boards for use with UEI’s “Cube” and RACKtangle I/O series respsectively. The DIO-452 boards are designed for use in a wide variety of switching and digital control applications. Each channel is configured as a standard Form C (SPDT) relay and switches voltages up to 100 VDC or 150 VAC. Each channel is rated for continuous operation at 2 Amps @ 30 VDC and 0.75 Amp at 125 VAC with an output voltage of less than 200 mV (<200 mOhm).

All relays default to “off” on power up/reset. Switching rates up to 125 Hz are supported. Each relay is protected by an on-board 2 Amp slow-blow fuse.

All connections are made through a convenient 37-pin D connector ensuring no problems obtaining mating cables or connectors. Users may also connect the DNx-DIO-452 boards to our popular DNA-STP-37 screw terminal panel via the DNA-CBL-37S cables. The cables are fully shielded and are available in 1, 3, 10 and 20 foot lengths.

The DNx-DIO-452 series includes software drivers supporting all popular operating systems including: Windows, Linux, QNX, VXWorks, RTX, and other popular Real-Time Operating Systems. Windows users may take advantage or the powerful UEIDAQ Framework which provides a simple and complete software interface to all popular Windows programming languages and data acquisition and control applications (e.g. LabVIEW, DASYLab, MATLAB).

Comments

Post a Comment

Popular posts from this blog

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more