Lincoln Adds Kohler Engine to Outback 145 Welder

Lincoln Electric has added a Kohler 9.5HP Model CH395 overhead cam (OHC) gasoline engine to its Outback 145 welder, which is suitable for jobsites and outdoor welding applications. The welder is designed for applications that require a rugged and easily portable machine that includes a reliable generator. This unit is specifically designed for contractors, maintenance crews, farmers and ranchers, as well as for use on service trucks where portable DC stick welding and AC generator power is needed.

The new Outback 145's Kohler engine features a cast-iron cylinder liner for long engine life as well as automatic shutdown for low oil level and a three-year engine warranty. The unit delivers 145A of smooth DC output welding for use with up to 1/8in stick electrodes on steel, stainless steel, cast iron and hard-facing projects. Its single, full-range, calibrated welding output dial makes it straightforward to set the best current for any maintenance, fabrication or repair project. The Outback 145 high-capacity AC generator provides 4,750W peak power and 4,250W of continuous power for accessories such as grinders, work lights and pumps.

It can also provide emergency backup power if needed. A low-cost Lincoln Electric Power MIG 140C or Power MIG 180C compact MIG wire welders can also be plugged into the 240V receptacle without an adapter for high-productivity wire welding. Weighing 234lb, the Outback 145 features Lincoln's Low-Lift grab bars, providing increased leverage for lifting the unit on and off truck beds and extra protection against damage. The rugged 1-1/4in-diameter tube frame provides sturdy all-around protection. The 6.8-gallon fuel tank offers extended run times and less frequent refuelling than comparable welder/generators, according to the company. The tank also includes a large fill opening.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more