Dry Pressure Gauge for Corrosive Atmospheres

Baumer's industrial pressure gauge MEX5 is designed for use in corrosive atmospheres and fluids. The gauge with its diameter of 100mm comes with a dashpot that makes it highly resistant to vibration, eliminating the need for a dampening liquid. The MEX5 is mainly intended for process industries such as the chemical, petro-chemical, energy, or gas industries. With its Lloyd's Register, Atex and GOST approvals, it can also be used for measuring the pressure in tanks on ships.

The MEX5 has a stainless-steel sensing element and fully welded process connection. The gauge offers an accuracy class of one according to European norm EN 837-1 and conforms to Pressure Directive PED 97/23/CE. The sealed stainless-steel case of the MEX5 can be filled with a dampening fluid. Available options include water-glycerin and silicon. The dashpot available for the MEX5 series provides an alternative dampening method and can, in certain cases, replace the dampening fluid.

The mechanical dampening achieved by the dashpot amounts to +/-1.6 per cent of the measured pressure for the ranges 0-1 bar, 0-1.6 bar and 0-2.5 bar. For pressures of more than 2.5 bar, the dashpot achieves a mechanical dampening effect of +/-1 per cent.

Comments

Post a Comment

Popular posts from this blog

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more