New PROLINE® Overlapping Doors Feature an Industry-Leading One-Handle Design

Pentair Technical Products announces an enhanced single-handle design for Hoffman PROLINE® Overlapping Doors. The overlapping doors feature a master door to ensure a dust-tight seal with a three-point roller latch system operated by a PROLINE flush-swing handle. The innovative design now delivers sufficient compression with the single external handle, eliminating the two internal handles to significantly improve ease-of-use while maintaining the UL Type 12 rating. Doors are available as an optional PROLINE component or as a standard feature of the PROLINE Industrial Packages.

The overlapping master/adjacent door design allows unobstructed access to components housed in versatile PROLINE Industrial Enclosures, which house electrical and electronic equipment in industrial, local area networking and telecommunications applications. The master door is hinged on the right side and delivers a tight seal for full protection from dirt, dust, moisture, oil and other contaminants. The robust doors feature a rugged 14-gauge mild steel construction and are finished with RAL 7035 textured light-gray polyester powder paint. A removable door bar is also included on each door.

PROLINE Overlapping Doors are available in traditional 1200 mm and 1600 mm widths, as well as new 800 mm and 1000 mm widths. The new sizes provide reduced door opening radiuses, delivering an ideal solution for applications with limited aisle space.

 “PROLINE enclosures consist of a rugged frame that protects equipment as well as customer-selected tops, bases, covers, sides and doors, providing a customizable solution to suit a broad range of application requirements,” said Garrett Potvin, Product Manager. “The addition of the overlapping doors with a single handle—available standard on our industrial packages or as a PROLINE component—further expands this diverse offering, allowing quicker and easier access to components while still delivering a tight seal and a UL Type 12 rating.”

PROLINE Industrial Packages are fully featured, ready-to-use enclosure solutions that eliminate the need to order each component separately. For convenience, a single part number includes a frame, solid front door, solid rear cover, solid top, a gland plate, lifting eyes and a full subpanel. Side covers are ordered separately.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more