Fox Now Offers Widest Range of AEC-Q200-Qualified Crystal Oscillators

Fox Electronics, a leading global supplier of frequency control solutions, now offers the widest range of AEC-Q200-qualified crystal oscillators, which meet the stringent stress test requirements set for passive components used in automotive applications. The new oscillators are available with a frequency range of 2 MHz up to 135 MHz, -40°C to +85°C, with 2 MHz to 48 MHz available from -40°C to +125°C.

Certified to AEC grades 1-4 as well as to the ISO/TS-16949 specification, Fox's FA5xx and FA4xxx series withstand the rigorous environmental and operational conditions to which automobiles are subjected.

Due to their compliance with these stringent industry testing parameters, the oscillators are ideal for use in a variety of automotive safety and diagnostic applications, where reliability is critical to protecting the occupants. These include tire pressure monitoring systems (TPMS), navigation, antilock brake systems (ABS), air bags and proximity sensors. They can also be cost-effectively used for in-car multimedia applications, such as entertainment systems and back up cameras.

Frequency stabilities are as tight as ±25 ppm with aging of just ±5 ppm per year at 25°C. Standard configurations include package sizes of 7 mm x 5 mm and 5 mm x 3.2 mm in voltages of 1.8 V, 2.5 V or 3.3 V, with more options available upon request.

The seam-sealed oscillators are RoHS- and REACH-compliant with gold terminations. Both series feature an output load of 15 pF (HCMOS), a start-up time of 10 mS and a standby current of 10 uA as well as output disable and enable times of 100 nS and 10 mS, respectively. Output symmetry is 40% to 60%, with 45% to 55% available upon request.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more