BELDEN PRESENTS THE WORLD’S FIRST EIGHT-POLE M8 ACTUATOR/SENSOR CONNECTOR RANGE

Belden, a global leader in signal transmission solutions for mission-critical applications, introduces the world’s first eight-pole M8 actuator/sensor connector range. These connectors fulfill all requirements for shock and vibration resistance and come in two variants, molded cables and receptacles. All variants have a temperature range of -25°C to +80°C and are IP 67 rated when connected to their mating parts. These connectors provide high contact density – providing up to eight signals of transmission with an external power supply. The new eight-pole M8 actuator/sensor connectors are especially suitable for connecting optoelectronic sensors or safety switches typically found on monitoring safety doors machines and systems.

The single-ended molded connectors connect sensors or actuators to switch cabinets or distribution boxes and have an open cable end, which insures a high degree of flexibility in terms of wiring. The male connector (RSM 8-354/0.3 M) has a snap-in/threaded joint and the female connector (RKMV 8-354/2 M) has a self-locking threaded joint. Both molded bodies are made of thermoplastic polyurethane (TPU). The cordsets, which are available in polyvinyl chloride (PVC) or halogen-free polyurethane (PUR), have a cross-section of 0.25 mm2 and are available in 2-, 5- or 10-meter lengths. Other materials, cross sections and lengths are available upon request.

The receptacle connector RSMF 8/0.5 M has stranded wires, solder contacts, and a potted housing. These receptacles are ideally suited for use in switch cabinets or other machinery equipment. Conversely, the RSMEDG 8 is ideally suited for installation in sensors and is easy to install by means of a snap-in/threaded joint. An additional plug insert (RSEM 8) is available for various sensor housings that already have an M8 thread and/or snap-in joint. The housings of receptacle connectors are made of nickel-plated brass (RSMF 8/0.5 M and RSMEDG 8) or polyamide (RSEM 8).

Belden has set a further milestone in the area of connection technology with the new eight-pole M8 actuator/sensor connectors in the Lumberg Automation™ product range. According to Project Manager Frank Eilingsfeld, "This is the first time it has been possible to implement this many contacts in an IP 67-rated M8 connector, and it will be of benefit to all users who want to process a large number of signals in a confined space under tough environmental conditions. In addition, the product range offers a suitable solution for practically all installation requirements."

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more