5-Pin Circuit Board Adapter Han®

By combining the new 5-pin HARTING circuit board adapter with a Han® DDD module from the proven Han-Modular® series, it is now possible to create a multi-pin connector on a device’s printed circuit board. The circuit board adapter can be pre-assembled on the PCB by following the hole pattern. A 17-pin circuit board connection is created for the Han® DDD module through connection of two 6-pin and the new 5-pin circuit board adapter. Here, the adapter can be assembled onto the PCB independently of the connector. After assembly of the PCB, the male or female contact of the Han® DDD module is installed in the housing and attached on the pre-assembled PCB. Simple assembly is not the only advantage – the labor involved in wiring is also kept to a minimum.

For connection to the circuit board, 17 contacts are available, with the following technical rated values as per DIN EN 61984:
  •     7.5 A rated current
  •     160 V rated voltage
  •     2.5 kV rated surge voltage at pollution grade 3
With this, the HARTING Han-Modular® series expands the product portfolio by a further variety of PCB adapter as well as the existing Han® DD solutions and the Han® 40 A module.
With the open Han-Modular® connector system, the user can assemble a connector to his own individual requirements. This provides over 40 different modules for electrical, optical and pneumatic transmissions.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more