HLG-80H-C Series (90W High Output Voltage LED Power Supply)

After the launch of low output voltage and high current rating LED power supplies ~ HLG-40H~320H series (40W~320W), MEAN WELL introduced the new 90W high output voltage and low current rating LED driver ~ HLG-80H-C series. Possessing 350mA (257VDC max. output) or 700mA (129VDC max. output) rated constant current, HLG-80H-C series are suitable for LED lighting fixtures that require to connect numerous LEDs in one single strip to high voltage rating. Under this design, the LEDs can get the perfect constant driving current as well as the long lifetime. With wide input range of 90~305VAC, HLG-80H-C series not only fit for general 115VAC or 230VAC main input, but also can be operated under 277VAC input in North America. Besides, considering the influence of dust and moisture from outdoor or indoor harsh environment, these new series are fully potted by glue (IP65/67 structure) and enclosed by aluminum case.

With constant voltage (C.V.) plus constant current (C.C.) design, HLG-80H-C series are built-in two-stage active PFC function and comply with harmonic current limitation per EN61000-3-2 Class C (>50% load). They also fulfill PF>0.9 if loading over 50% and possess 4kV surge immunity (EN61000-4-5) ability which complies with the requirements of street lighting. With up-to-date high efficiency topology, HLG-80H-C series possess up to 92% of high efficiency, so they can be cooled by free air convection from -40℃ to +70℃ ambient temperature that meet the high temperature requirement of closed lighting system. Besides standard functions of protections for short circuit, over voltage, and over temperature, these power units provide dimming options of “three-in-one dimming function “(B type) or “timer dimming function” (D type). Comply with global certificates per UL/ CUL/ TUV/ CB/ CE, including UL8750, EN61347-1, EN61347-2-13 of lighting regulations, your safety can be greatly guaranteed. Suitable applications include LED street lighting, LED tunnel lighting, LED spot lighting, LED decorative lighting, and other indoor/outdoor LED lighting etc.
  • Wide range input 90~305VAC
  • Built-in active PFC function
  • 92% high efficiency
  • Aluminum case and potted by glue, comply with IP65/67
  • Output current adjustable (refer to the below table)
  • Meet 4kV surge immunity level (EN61000-4-5)
  • -40~+70℃working temperature
  • Cooling by free air convection
  • Protections: Short circuit / Over voltage / Over temperature
  • Certificates: UL / CUL / TUV / CB / CE

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more