Aaxeon Releases New Industrial 12-Port Managed Ethernet Switch

Aaxeon Technologies is proud to announce the release of our new LNX-1212GN-SFP-T Industrial 12-port Managed Gigabit Ethernet Switch.  The LNX-1212GN-SFP-T is a managed redundant ring Ethernet switch with 8 x Gigabit combo ports and 4 x 1000BaseX SFP ports. With complete support of Ethernet Redundancy protocol, Redundant Ring (recovery time < 20ms over 250 units of connection), and MSTP/RSTP/STP (IEEE 802.1s/w/D), the LNX-1212GN-SFP-T can protect your critical applications from network interruptions or temporary malfunctions with its fast recovery technology.  It can provide advanced IP based bandwidth management that can limit the maximum bandwidth for each IP device. Users can configure IP cameras and NVR with more bandwidth and limit other device bandwidth.

The LNX-1212GN-SFP-T also supports application based QoS.  Application based QoS can set the highest priority for data streams according to the TCP/UDP port number.  The IP police function can permit only allowed IP addresses with MAC addresses to access the network.  Hackers cannot access the IP surveillance network without permission.  It can prevent hackers from stealing private video data and from attacking IP cameras, NVRs and controllers.  The LNX-1212GN-SFP-T also provides advanced DOS/DDOS auto prevention.  If an IP flow becomes too big in short period of time, the switch will lock the source IP address for a set amount of time to prevent the attack.  Its hardware based prevention helps prevent DDOS attack without using CPU resource.  The switch can also be managed via a Web-based interface, Telnet and console (CLI) configuration.  The LNX-1212GN-SFP-T is one of the most reliable choices for highly-managed Gigabit Fiber Ethernet applications.

Key Features:
  • 8 x Gigabit combo ports and 4 x 1000BaseX SFP ports
  • Jumbo frame up to 9K Bytes
  • Redundant Ring (recovery time < 20ms over 250 units of connection), MSTP/RSTP/STP (IEEE 802.1s/w/D) for Ethernet Redundancy
  • Supports IP based bandwidth management
  • Supports application based QoS management
  • Supports IP police security function
  • Supports DOS/DDOS auto prevention
  • Supports DDM (Digital Diagnostic Monitoring) function (P1 ~ P8)
  • IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic
  • Supports SNMP v1/v2c/v3, RMON and 802.1Q VLAN Network Management
  • Support ACL, 802.1x User Authentication for security
  • Multiple notification for warning of unexpected event
  • Configurable by Web-based interface, Telnet and Console (CLI)
  • Supports LLDP Protocol
  • Rigid IP-30 housing design
  • DIN-Rail and wall mounting enabled

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more