Adept Introduces UEI 12-Channel Relay Boards

Adept Scientific has announced it is now offering 12-channel, electromechanical relay boards from United Electronic Industries (UEI) for use in switching and digital control applications. The DNA/DNR-DIO-452/462 relay boards are designed for use with UEI's Cube and Racktangle I/O series respectively. Each channel is configured as a standard Form C (SPDT) relay and switches voltages up to 100V DC or 150V AC.

Each channel is rated for continuous operation at 2A at 30V DC and 0.75A at 125V AC with an output voltage of less than 200mV (less than 200mohm). All relays default to 'off' on power-up/reset and switching rates up to 125Hz are supported. Each relay is protected by an on-board 2A slow-blow fuse. All connections are made through a 37-pin D connector ensuring no problems when mating cables or connectors. Users may also connect the DNx-DIO-452/462 boards to UEI's DNA-STP-37 screw terminal panel via the DNA-CBL-37S cables.

The cables are fully shielded and are available in 1ft, 3ft, 10ft and 20ft lengths. The DNx-DIO-452/462 series includes software drivers supporting operating systems such as Windows, Linux, QNX, VXWorks, RTX and other real-time operating systems. Windows users may make use of the UEIDAQ Framework, which provides a complete software interface to all popular Windows programming languages and data acquisition and control applications.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more