WAGO IEC-Compatible TeleController and I/O-IPCs

WAGO Corporation’s IEC-compatible TeleControl PLC and four Linux-equipped I/O-IPCs are comprehensive solutions for both control and smart grid integration. These WAGO-I/O-SYSTEM components support IEC 60870-5-101 (serial transmission), IEC 60870-5-104 (TCP/IP-based communication) and IEC 61850 (substation protection/control). This permits use of one DIN-rail mount device for automation and IEC communication, conserving engineering resources.

Programmable via CoDeSys 2.3, WAGO’s TeleController and I/O-IPCs convert signals from process/telecontrol apps via connected I/O into IEC-compliant data. This simplifies monitoring of supply networks/transformers, integration of both pumped-storage and hydroelectric power plants into a control system, as well as networking wind/solar farms.

TeleControl PLC:
The 32-bit 750-872 TeleControl PLC provides application protocols for data acquisition/control (MODBUS TCP/RTU, ETHERNET I/P) or management/diagnostics (e.g., HTTP, BootP, FTP and more).

Linux 2.6 I/O-IPC-G2:
The 758-870 is available as a Linux 2.6 Master (PROFIBUS DP or CANopen) or Slave (PROFIBUS DP) — both with a 266 MHz Geode™ processor. The Linux-backed 758-875 I/O-IPC-G2 is available with a 1 GHz Celeron®M processor as a PROFIBUS DP or CANopen Master for extended application ranges. All 758 Series I/O-IPC-G2 Masters can double as a main PLC for industrial applications.

The Telecontrol components are compatible with the WAGO-I/O-SYSTEM’s 400+ digital, analog, specialty and Ex-i-compliant modules for custom applications. Both the TeleController and I/O-IPC-G2 units pair with Ex-i-components to eliminate EX-barriers within hazardous control applications, e.g., petrochem. They also provide capital asset management via WAGO’s Vibration Monitoring and 3-Phase Power Measurement I/O.

WAGO is the leader in spring pressure connection technology that eliminates loose wires resulting from vibration and temperature cycling, while providing highly reliable, corrosion-resistant and maintenance-free connections. Products: DIN-rail, PCB and chassis mount terminal blocks; signal conditioners; the WAGO-I/O-SYSTEM and more.

Comments

Post a Comment

Popular posts from this blog

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more