Connector Meets Roadside-Lighting Legislation

Molex has introduced a power quick-disconnect connector designed to meet new EU legislation for roadside lighting and electronic signage. The passive safety pole connector is said to dramatically speed up installation, repair and temporary removal of street furniture. The road-safety legislation stipulates necessary changes in roadside furniture construction and materials to better absorb impact and lessen personal injury of motorists in the event of a crash.

Changes in safety regulations will specifically require that all powered signs, lights and signals include a power quick-disconnect system; standards relative to the product include TA 89/05, BS EN 12767 and BS EN 60309-1and2. In the event of an accident, whereby a vehicle hits roadside equipment, the system must disconnect the electrical supply within 0.4 seconds of impact. Motion sensors and circuit-protection devices available on the market do not prevent tearing or tethering of wires on impact with a pole.

The passive safety pole connector includes safety devices and systems that operate without need for human input or action. Installation of the Molex pole connector is a two-step process. During step one, base fixtures of the pole are cemented into the ground. The first cable, fitted with a connector sealed by a water-tight cap, is installed into the ground at the main circuit-protection device. The integrated protective cap remains in place until the connector is mated with the pole-side connector, and provides mechanical and environmental protection for the interface (IP68).

This is an important feature, as there can be several weeks or even months where the ground-side connector is installed without the pole being present. In the event of a pole being destroyed, the cap can simply be pushed onto the connector, providing protection for the contact interface and ensuring the safety of the public and construction crews. The second step is to install the pole and connect the pole cable to the ground cable. A flexible tether attaches the pole over or underground.

The connector and cable are pre-assembled when manufactured to protect them fully from external elements, while saving time and money during installation. In addition to roads, highways and motorways where power is used, the Molex passive safety pole connector can be used in any application requiring a quick-release safety connection. Low extraction forces combined with IP68 sealing and high electrical and mechanical performance capabilities ensure that the passive safety pole connector is suitable for generators at docks, electric cars, golf buggies and carts; emergency vehicles; and temporary speaker and lighting installations at open-air concerts.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more