Courses Aid Installation of Small Bore Tubing

A new approach to training for best-practice installation of small bore tubing systems has been launched by the Instrumentation Products Division of Parker Hannifin. The company's Small Bore Expert (SBEx) courses provide a detailed and personalised understanding that allows users to specify and install efficient, safe and leak-free small bore tubing systems. Small bore tubing systems are used in a range of industries, ranging from fluid instrumentation systems in processing plants to laboratory equipment.

Parker's SBEx course replaces its Safety at Work programme and places greater emphasis on small bore tubing issues, including tube selection, fittings and installation. Each course lasts half a day, or a full day if participants wish to gain practical hands-on experience of preparation, cutting, bending, installation and verifying connection integrity. SBEx courses are run by professionally trained and equipped Parker distributors. They are currently available from four key UK distributors in the UK, with a further 95 lined up to extend the service level across Europe.

The courses will also be run by Parker's 22 direct sales facilities and become available in the Middle East and Africa in the future. Parker's SBEx courses can be run at distributors' or customers' premises, or at one of Parker's facilities. Depending upon availability, there is also the possibility that the Parker mobile exhibition vehicle can be used by distributors to provide customer training facilities. Parker distributors will shortly begin actively promoting the SBEx courses to their customer bases.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more