congatec Introduces New conga-BP77 COM Express Type 2 Module with 3rd Generation Intel® Core™ Processor

congatec AG, a leading manufacturer of embedded computer modules, adds the conga-BP77 to its portfolio of 3rd generation Intel® Core™ modules. This version is based on the COM Express Type 2 connector pin-out and supports the PCI Express graphics port for high-performance external graphics.

The conga-BP77 module version is therefore well suited to medical, gaming and multimedia applications needing high end graphics performance, for which the internal graphics support from the chip set no longer suffices. The PEG connection is implemented via a customised carrier board. The freely available schematics for the evaluation carrier board conga-CEVAL provide the perfect baseline for developing proprietary solutions.

The crucial innovations of the 3rd generation Intel® Core™ processors relate to the use of 3D trigate transistor technology, 22 nanometer production, more tightly integrated graphics and the improved PEG 3.0 graphics. The change from PEG 2.0 to PEG 3.0 is the performance increase from 5 GT/s to 8 GT/s.

The conga-BP77 is available off the shelf now in the processor versions Intel® Core™ i7-3612QE (4 x 2.1 GHz, 6 MB Intel® Smart Cache, TDP 35W), Intel® Core™ i7-3555LE (2.50 GHz, 4 MB Intel® Smart Cache, 25W) and Intel® Core™ i5-3610ME (2.7 GHz, 3 MB Intel® Smart Cache, 35W). The module features the new mobile Intel® Express chip set QM77 and offers up to 16 GByte dual channel DDR3 memory (1600 MT/s).

Six PCI Express 2.0 lanes, four SATA interfaces with up to 6 GB/s and RAID support, eight USB 2.0 ports, one EIDE and one Gigabit Ethernet interface facilitate fast and flexible system extensions. Besides PEG 3.0, VGA and LVDS are supported, as well as DirectX 11, OpenGL 3.1 and OpenCL 1.1. Fan control, LPC bus for easy connection of legacy I/O interfaces and the Intel® high definition audio round off the set of functions.

All conga-BP77 modules are fitted with the new embedded firmware solution, UEFI. Under UEFI, congatec's embedded BIOS features are also supported and extended. Even larger applications can now be integrated with the new pre-boot application. This way, for example, embedded diagnostic tools, network-based service programs or system recovery applications can be used regardless of the operating systems.

A matching evaluation carrier board for COM Express Type 2 enabling fast implementation of a PCI Express graphics x16-lane plug is also available.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more