Sit-Down Lift Trucks Handle up to 10,000lb Loads

Linde Material Handling North America has introduced its RX60 series of electric counterbalanced sit-down lift trucks for manufacturing, storage and distribution, and logistics businesses. The eight models in the series have capacities ranging from 5,000lb (RX60-25C and RX60-25L) to 10,000lb (RX60-50). The RX60-25C and RX60-30C feature cushion drive and steer tires, while the six remaining trucks in the series have SE drive and steer tires as standard equipment.

The new rail design of the trucks strengthens the mast and limits deflection. Travel speeds of 12mph and lift speeds of 100fpm enable these trucks to operate in place of engine-powered units. The trucks feature automatic power boosts that are activated when the system sensors demand, to negotiate railroad crossings, curbs, steep ramps or other obstacles, for example. The RX60 Series has been designed to minimise strain on the operator throughout the day. The trucks each feature low noise levels (68dba), a floating operator compartment, tilted floorboard, a fully adjustable suspension seat and an adjustable steering column.

All components and assemblies are tested to meet rigorous longevity standards. The heavy-duty cast ductile iron steering axle provides a strong structure. Electrical component placement inside the counterweight offers protection. The counterweight dissipates naturally occurring heat during operation. Thermal protectors monitor components and limit power output in case of high temperature. The 80V electrical system has maintenance-free enclosed motors and is said to provide performance comparable to LP and diesel-powered forklifts.

The large battery compartments accommodate standard and vented batteries. A fast-charge assist is also available as an option. High visibility of the load and through the mast - a key element for forklift safety - is accomplished via the rail design and two free-lift cylinders instead of one. All performance parameters are adjustable to adapt to different operating conditions and customer requirements. The 'ramp start assist' function helps the operator with stopping and starting on inclines.

Both indoor and outdoor operations can be handled by the RX60. When equipped with full cab and electric heater, the RX60 functions in severe weather. Fitted with cold storage equipment, it will also work in freezers with temperatures as low as -20F. The use of the dual front tires adds additional stability for wide loads or at high lift heights. The energy return system can extend battery life by up to 15 per cent. Energy use is limited and component life extended as all high-voltage components are mounted to the counterweight.

Blue-Zone memory adaptive software maximises truck efficiencies based on individual operator driving characteristics, resulting in additional energy savings of up to 20 per cent. The RX60 has extended 1,000-hour maintenance intervals, while design features such as automatic deceleration, dual independent CAN-Bus control systems, maintenance-free brakes and continuous on-board diagnostics are designed to make it easier to maintain ideal working conditions. The three-phase AC system operates without brushes and is completely sealed, extending component life and reducing maintenance expenses.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more