Hielscher Offers Industrial Ultrasonic Processor

Hielscher Ultrasonics has introduced the UIP1500hd (20kHz, 1,500W) industrial ultrasonic processor, designed for use under difficult conditions and continuous high-power operation. The UIP1500's transducer meets the IP65 standard. The ultrasonic processor can be used in research and development and industrial production of smaller volumes. Typical flow rates are between 0.5 and 6.01/min (or 1 to 8m/day). It is suitable for the sonication of different materials in many process application, such as for nanomaterials, paint and ink, food, cosmetics and biodiesel production.

The UIP1500hd is commonly used for inline sonication (single pass or loop) in order to obtain better processing quality. It can also be used for batch sonication. The UIP1500hd allows for running at a wide range of ultrasonic parameter sets. Users can vary ultrasonic amplitude, liquid pressure and liquid composition, such as: sonotrode amplitudes of up to 170 micron; liquid pressures of up to 10 bar; liquid flow rates of up to 15 litres/min (depending on the process); liquid temperatures of up to 80C (other temperatures on request); and material viscosity of up to 100,000cp.

The UIP1500hd is said to offer exact reproducibility and linear scalability. Any sonication setup can be reproduced and can be used at continuous operation or can be scaled up to any larger unit. Hielscher offers a range of accessories, such as sonotrodes, boosters, flow-cell reactors and sound protection boxes. The PC-Control (optional software interface) allows for the recording of the individual test runs.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more