CT Analyzer - a Revolution in Current Transformer Testing

The CT Analyzer provides fast and cost-effective testing and verification of current transfor-mers for protection and metering applications. It automatically determines all relevant current transformer values and compares the results with the selected IEC or IEEE standard. The very small and lightweight (< 8kg) device offers an outstanding accuracy of 0.02 % in ratio and 1 min in phase angle deviation, making it the most suitable mobile test device for testing CTs up to accuracy class 0.1.
The latest version of the CT Analyzer has been improved with new hardware accessories and software functions.

The latest measurement function of the CT Analyzer - the RemAlyzer - allows current trans-formers to be tested for residual magnetism. Residual magnetism can occur when current transformers are confronted with very high AC currents or DC offset during fault conditions. Core saturation effects caused by residual magnetism may lead to incorrect operation of the protection relays.

The CT Analyzer can be extended by the CT SB2 switch box, enabling testing of current transformers with multiple taps, without the need for rewiring. The CT SB2 is a standalone unit, which can be attached to the CT Analyzer. It provides simple, color-coded, six-channel connection possibilities, guaranteeing convenient wiring and avoiding time-consuming and error-prone reconnection. Due to its wide functionality range and easy handling the CT Analyzer is the ideal solution for on-site testing and calibration of single and multi-tap current transformers for protection and metering purposes.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more