IDC’s Wireless PCB Board Enables Savings of up to £80 Per Year/Per Desk to be Achieved in Energy Intensive Offices

Wireless networking and automation specialist, IDC has developed a ZigBee-based PCB, which slots into eco2TM power blocks manufactured by CMD Ltd to provide energy saving in general offices. With this system, savings of up to 60% per year (equating to £80 per year/per desk) are achievable, simply by automatically powering down PCs and non essential equipment when not in use.

The eco2TM power block is the ideal product to reduce the carbon footprint of energy intensive offices such as call centres, stock dealing floors, foreign exchanges, banking centres and government facilities. It is easy to use, integrating a single primary power sensitive socket, and either five or three secondary sockets (depending upon the socket unit chosen).

The primary (red) socket is designed to accommodate the user’s PC, with the secondary sockets for other functions such as printers, monitors, scanners, (etc). The primary is programmed to switch off the power to the secondary sockets when its own power value drops below the normal (i.e. in use) PC power level. This value can be set remotely over IDC’s ZigBee wireless network, which also includes a wireless gateway and hosted server, in addition to the bespoke OEM PCB.

The PCB itself comprises a relay – for switching off mains power, two shunts and a metering chip, which measure the power consumed by the primary red socket and the total power taken by all sockets. The PCB also measures amps, volts, and power factor readings, all of which can be logged in IDC’s hosted server by the wireless gateway. This facility enables central analysis of the power that is being consumed by large numbers of power blocks, enabling efficiency comparisons and power savings to be calculated.

“With all the focus on energy saving in industry, people have forgotten about the vast amounts of energy that are being wasted in offices, by leaving equipment on when it is not being used,” said Kevin Buckley, MD of IDC. “ZigBee wireless technology is the ideal tool to rectify this situation. One of the technology’s first uses was in home automation, providing two-way communications that enabled building operators to monitor and keep track of their utilities usage, and then feed this data to a computer system for data analysis. In addition, ZigBee offers the additional advantage that it can be incorporated into small inexpensive chips that consume little power – making it easy to integrate into the eco2 power blocks.”

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more