Medical Grade Epoxy Adhesive Withstands High Temperatures and Repeated Sterilization

Capable of tolerating the harsh environments of the medical industry, Master Bond EP42HT-2ND2Med Black fully complies with the testing requirements of USP Class VI plastics. This two component epoxy resists recurrent autoclaving and sterilizations including radiation, steam, ethylene oxide, and chemical sterilants.

EP42HT-2ND2Med Black is an excellent electrical insulator with a volume resistivity over 1012 ohm-cm, a thermal expansion coefficient of 35 to 40 in/in x 10-6/°C, a dielectric constant of 3.8, and a tensile strength exceeding 12,000 psi at ambient temperatures. Heat resistant up to 450°F, it also withstands chemicals such as inorganic and organic acids, alkalis, organic solvents, and aromatic hydrocarbons.

This epoxy conveniently cures at room temperature in 48 to 72 hours. Its optimal curing schedule is overnight at room temperature followed by 2 to 3 hours of heat curing at 100°C to 125°C. EP42HT-2ND2Med Black has a noncritical mix ratio of 100:40 by weight or 100:50 by volume, and a paste consistency with minimal flow when applied. It offers a lengthy working life of 30 to 45 minutes for a mixed 100 gram batch at ambient temperatures, which can be increased by using shallow mixing vessels or mixing smaller batches. Parts A and B for EP42HT-2ND2Med Black are available for use in syringes, half pints, pints, quarts, gallons, and five gallon containers.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more