Half the Size of Standard 1200 V IPM's - Increased Power Density for Higher Efficiency

Interchangeble with every countryNuremberg, 10 November 2010 – The MiniSKiiP IPM from SEMIKRON sets a new benchmark for power density in 1200V Intelligent Power Modules. At a weight of 55g and a volume of 49cm³, this module is lighter and more compact than any other IPM module in this power class. Plus, the design yields optimum switching properties with regard to electromagnetic interference. This module was developed for inverter applications of up to 15kW.

With an area of 59mm x 52mm and an overall height of 16mm, this module is at least fifty percent smaller than conventional intelligent power modules in this power range. The innovative connection technology allows for the development of compact inverters and reduced production costs.

To achieve the high power density offered in the MiniSKiiP® IPM module, the power semiconductor chips and the DCB are thermally connected to the heat sink by way of an efficient pressure contact system. Since the module does not contain a base plate, the thermal resistance is much lower than in any other IPM with base plate.

The integrated SOI driver is mounted directly onto the DCB and connected to the gate terminals of the power transistors by short conductor lines via optimised gate resistors. These short connections ensure harmonious switching behaviour and reduce electromagnetic interference. As a result, less complex protection measures are needed to comply with the electromagnetic compatibility requirements. The short paths result in low parasitic inductances, which in turn mean lower over-voltages in the module, allowing for higher DC link voltages and greater efficiency.

The MiniSKiiP® IPM module and the power circuit board are mounted to the heat sink using a single standard screw. The entire power, gate and auxiliary connections are made by way of pressure contacts to the PCB rather than soldered contacts. This allows for quick and cost-reduced assembly. Plus, the removal of solders further improves the quality of the entire construction and brings about a higher degree of reliability than in conventional IPM modules. Users profit from the user-friendly design of this all-inclusive product as compared with discrete solutions.

The 1200V 6-pack MiniSKiiP® IPM has a high-voltage driver IC and features state-of-the-art Trench-Field-Stop IGBTs, which are optimised for low switching losses and high current densities. At a rated current of 61A, an output power of up to 15kW is possible. 600V Converter-Inverter-Brake versions are also available. The modules fully comply with the requirements of the EU RoHS directive.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more