Essemtec Launches Radial Component Feeder

Essemtec has launched the CLM979 radial component feeder that enables the assembly of through-hole LEDs on a standard pick-and-place machine. The feeder releases LEDs from the tape, cuts the wire ends and prepares the component for pickup. Typically two different machines have been required for mixed placements: an SMD pick-and-place and a placement machine for conventional components. However, with the CLM979 radial feeder, a pick-and-place can accomplish both through-hole LED assembly and SMD placement.

Essemtec said this saves space, time and money. The LEDs are supplied in radial tapes. The CLM979 feeder transports the components, releases them from the tape, cuts the wire ends to the desired length and aligns them parallel. So-prepared LEDs can now be handled by the SMD pick-and-place with a vacuum pickup tool.

In order to guarantee smooth insertion of the LEDs into the soldering holes, the wire ends are inspected using optical systems (laser and vision). If the wires are bent out of tolerance, because of a bent terminal, for example, the component is rejected. The CLM979 feeder can be mounted in parallel to standard SMD component feeders - therefore, mixed placement is possible in one run.

Depending on the application, through-hole LEDs can be soldered using the solder wave or reflow soldering system (pin-in-paste technology). The radial feeder CLM979 is said to expand the application range of a standard SMD placement machine and increases flexibility. The feeder is compatible with most of Essemtec's automatic pick-and-place machines. It also can be retrofitted on machines of other brands.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more