ZMDI Launches Highly Efficient Boost Converter to Drive Multiple High Brightness LEDs in Low-Voltage Lighting Applications

ZMD AG, a global supplier of analog and mixed-signal solutions for automotive, industrial, and medical applications, is introducing its first step-up converter with integrated 35 V power switch for high brightness LEDs. It is optimal for driving multiple white LEDs connected in series from a low voltage supply. The ZLED7015 can also drive devices that require a constant voltage and the wide input voltage range of 6V to 30V supports applications with input voltage from multi-cell batteries or regulated 12V and 24V power rails. A low voltage feedback mechanism helps maximize the operating efficiency and the device’s soft-start function and open circuit detection protects the application circuit and extends the LED life.

The low voltage, constant current operation makes the ZLED7015 an ideal choice for safety extra-low voltage (SELV) applications with less than 24V in damp environments. The device is also an ideal driver for multifaceted reflector (MR16) lamps, frequently found in residential and retail lighting applications. Other key application areas include low voltage retrofit lighting, replacement tubes, LED backlighting, aftermarket automotive lighting products, low voltage general purpose industrial and consumer applications, as well as signage, outdoor, architectural and building lighting.

„The step up topology of the ZLED7015 enables applications using multiple high brightness LEDs strings while being driven from a low voltage source“, stated Andy Smith, Product Manager at ZMDI. “This is particularly attractive for designers of low voltage high brightness lighting products. Other benefits include simplified manufacturing, lower cost, higher efficiency and greater reliability.“

The ZLED7015 is ideal for customers using 6-30V supply to drive multiple high brightness LEDs. The device includes an integrated power switch to minimize system cost and reduce component count for size optimized applications. The output current is programmable via external components and features PWM, Linear and DC voltage dimming.

The ZLED7015 operates with a switching frequency up to 1MHz allowing the use of smaller, less expensive external components. A low 0.3V feedback voltage minimizes power loss in the current setting resistor for better efficiency. With an adjustable over voltage protection, the chip and the system operates safely even if the load is not connected or the output is short circuited.

A built-in soft start circuit significantly reduces the inrush current during start-up and extends the LEDs lifetime. Further features include an under voltage protection as well as an over temperature protection.

The operating temperature range of the ZLED7015 is -40°C to 85°C. Samples and a complete evaluation kit are available now. The ZLED7015 comes in a MSOP-10 package and is RoHS compliant. For 5,000 pieces, the ZLED7015 is priced at €0.35/$0.46.

Comments

Post a Comment

Popular posts from this blog

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more