Power Supplies Provide No-Load Power Consumption

The Mean Well HRP-100 series has been designed for any application that requires no-load power consumption and a power supply with power-factor correction. The HRP-100 series, along with the existing range of products HRP-75, HRPG-150, HRPG-300 and HRPG-600, allows Ecopac Power to offer the full range of Mean Well 75 to 600W miniature enclosed power supplies all with PFC function and energy-saving functions.

Featuring low no-load power consumption, operating efficiency of 90 per cent and miniaturisation, the Mean Well HRP-100 series reduces the size and increases the working efficiency in comparison to the existing range of 100W power supplies. Mean Well has reduced the size of the HRP-100 by 26.5 per cent compared with its first generation of PFC models, the SP-100 series, and has increased the working efficiency between 4.5 and eight per cent. The HRP-100 series has a profile of less than 1U, with overall dimensions of 159 (l) x 97 (h) x 38mm (w). With a five-year warranty, the HRP-100 series complies with Energy Star and operates at -30 to 60C.

As the units have a no-load power consumption of less than 0.5W, designers can conform with the requirements of Energy Star and EuP for end-user systems and applications. With a universal input of 85 to 264V AC and built-in active PFC function, the units are designed to withstand 300V AC surge for 5sec, including short-circuit, overload, over-voltage and an optional over-temperature protection. The Mean Well HRP-100 series are supplied with worldwide safety certificates UL, CUL, TUV, CE and CB.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more