Aaeon Launches ETX-CX700M Product

Aaeon has announced the ETX-CX700M - an Embedded Technology Extended (ETX) product based on the VIA C7/Eden (V4) series processors combined with the VIA CX700M chipset. The ETX-CX700M provides support for a multitude of expansion and storage interfaces that will allow for numerous options to be designed onto the baseboard. The module is available with either the VIA Eden 1.6GHz processor or the VIA C7 2.0 GHz processor and features support for one 200-pin DDRII 400/533 RAM at a maximum capacity of 1GB.

It has support for four 32-bit PCI buses, one 8-bit/16-bit ISA bus, one SMBus, and one I2C bus that enable the customers to expand on their systems without the extra cost of hubs. For Ethernet support, the ETX-CX700M features the Realtek RTL8139DL 10/100Mb Ethernet chipset with the option for customers to change to the Intel 82551QM 10/100Mb chipset as needed for their application.

Video support is handled by the VIA CX700M chipset and can provide resolutions up to 1,600 x 1,200 on a 24-bit dual-channel LVDS LCD panel, as well as a CRT monitor. The module supports simultaneous and dual-view output to CRT/LVDS, LVDS/TV, CRT/DVI or TV/DVI. The integrated video on the board can share up to 128MB of system memory for use as video memory and it supports an MPEG-4 accelerator.

Storage support is available by means of two SATA II connectors on the ETX-CX700M as well as with support for one PATA channel and Compactflash on the carrier board. The ETX-CX700M aims at markets such as test and measurement, gaming and entertainment, industrial automation, military, government and security.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more