HD Cameras for Industrial Inspection Applications

Toshiba Imaging has announced an OEM relationship with Dage-MTI to introduce two high-definition cameras designed specifically for microscopy applications. Dage-MTI's Realview HD microscope cameras are said to combine Toshiba Imaging's proprietary imaging technology with specially formatted, preset values for use in critical microscopy applications. The single-chip Realview HD-120 microscope camera operates at 1,080 pixels, 60fps, and features excellent detail from the 2.1 million pixel sensor.

The real-time HD image provides true 1,920 x 1,080 resolution, and matches the pixel-to-pixel resolution of the 16x9 ratio HD monitors and DLP projectors, without vertical and horizontal stretching. Viewing is described as intuitive and effective in settings such as tumour review boards, clinical rounds, pathology laboratories, classrooms, industrial inspection and more. Dage-MTI's Realview HD-330 microscope camera offers fast frame rate operation in 1,080i mode at 30fps and features smooth motion.

The high signal-to-noise ratio is said to enable good sensitivity with clear definition and colour contrast, even in low-light conditions. Dage-MTI has incorporated Toshiba Imaging's 3CCD prism block camera technology to ensure sharp HD colour imagery. The three-chip camera is designed for use in applications such as pathology laboratories, cell biology, fluorescent imaging, classroom or other teaching environments, and industrial inspection.

The HD cameras are also said to be suitable for ophthalmic and dental surgery. Both Realview HD microscopy cameras can be connected directly to high-definition monitors via DVI-output or HDMI cables, eliminating the need for software or a PC. The cameras can be paired with Dage-MTI's Realview Magic Box.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more