HBM Amplifier Prevents Overloading In Warehouses

HBM has developed a digital amplifier that securely and permanently protects warehouse storage areas from overloading. The VKIA405 amplifier ensures the long-term stability of a storage system because it enables the monitoring of loads during operations and prevents any possibility of overloading in the storage area. Up to four analogue load cells can be connected to the new amplifier.

Storage lifts and automatic warehouses require special considerations for measurement technology, which is intended to minimise maintenance downtime. Maintenance interrupts continuous operations such as the removal and storage of goods, leading to high costs. It is important that long-term stability is a main criterion in the selection of measurement and weighing technology for these applications. The VKIA enables digital measured value processing with long-term stable supply voltage for the analogue load cells.

An HBM-tested off-centre load compensation network is integrated into the VKIA405 that simplifies installation as no additional wiring connection boxes for the load cells are needed. The VKIA405 is fitted with a serial RS485 interface, ensuring integration with the control and data processing system of a warehouse. A typical use of the VKIA405 is to integrate the amplifier and corresponding load cells at the charging station so they are part of the material flow. It is also suitable for simple weighing and monitoring tasks beyond legal-for-trade requirements.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more