Fujitsu Unveils Receipt And Journal Printer Units

Fujitsu Components Europe is releasing two ultra-low-profile, 24V, receipt and journal printer units that can either be combined together into one modular unit, or mounted separately. The FTP-627USL525/526 consists of two units: a 2in thermal receipt printer/cutter unit (FTP-627USL525) and a 2in journal printer/rewinder unit (FTP-627USL526).

The receipt printer unit measures 82mm (W) x 150mm (D) x 110mm (H), while the journaling unit measures 86mm (W) x 150mm (D) x 157mm (H). Both units weigh 350g. Designed for medium-duty applications, both the receipt and journal units have output speeds of up to 150mm per second and have an operating life of 100km of paper. The platen release mechanism on both the receipt and journaling unit resists paper jams. This ELM cutter jam-free concept implies that the moving blade is set at the platen side (open/close side) and the cover can be opened/closed when paper is jammed or cutter lock is on.

This easy paper-loading mechanism provides drop-in paper loading into a plastic paper bucket for rolls up to 58mm wide and 83mm in diameter. This design concept gives easy access to the rewinded paper roll of the journal printer. The receipt printer unit's guillotine cutter features its own dedicated stepper motor to deliver one million cuts at 20 cuts/minute. Full and partial cut are possible. The receipt and journal printer units offer high-definition printing with a resolution of 8dot/mm. Both units feature a die-cast frame that provides shock and vibration resistance, mounting stability, ESD absorption and static electricity dissipation.

It also enables combined or separate unit use, while ensuring suitability for many types of installations. The FTP-627USL525 and 526 can use the same interface as the FTP-627MCL401. This results in time and cost efficiency as no additional time needs to be spend on the design of a new controller board.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more