GAO Rolls Out Single-Mode-To-Multimode Converter

GAO Fiber Optics has rolled out a single-mode-to-multimode (SM-to-MM) converter operating in full-duplex mode. The modulated fibre-optic single-mode and multimode converter conducts the transparent conversion between the media of single-mode and multimode optical fibre and supports 100m quick Ethernet. It is intended for use in the interlinking and data communication fields of local-area networks and wide-area networks and for single-mode and multimode conversion.

The converter can connect FDDI, fast Ethernet or ATM using a 1,310nm wavelength for fibre-optic transmission. The SM-to-MM converter conforms to the IEEE82.3u and 100BASE-TX/FX standards. It is able to switch over among 1,310nm and 1,550nm single-mode fibres and 850nm and 1,310nm multimode fibres. The fast converter can be used as a standalone unit or as a slide-in module to GAO's 19in (48cm) converter rack or it can be used at a central wiring closet.

It supports centre chassis installation with optional power redundancy and management features for fibre networks. FX connectors are all SC. All of these features make the converter suitable for short-reach multimode fibres, long-reach single-mode fibres and Bi-Di and CWDM applications.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more