Pressure Regulators Ensure Constant Gas Supply

Dome-loaded 797 LE-HD gas-controlled pressure regulators from Witt can provide an economic and safe solution to ensure gas cutting systems receive a constant gas supply, according to the manufacturer. The company said this system of gas regulation is more economical than using a full electronic control system. In one application the three inlet lines for oxygen and propane are supplied via Witt pressure regulators to optimise the automatic gas supply.

The gas control was regulated using proportional valves with changes in the gas pressure being adjusted by pressure changes, thereby controlling the cutting process. Witt pressure regulators can be used for numerous applications with a range of flow rates and gases. They are used as a primary pressure regulator, which can be installed in any orientation, in gas supply pipeline systems to ensure a consistent stable pressure up to a flow of 2300m3/h and are independent of any inlet pressure fluctuations in the gas supplies, including gas withdrawals.

They are also suitable for use in shipyards, chemical processing plants, offshore and diving vessels, glass making as well as steel making and foundry applications. Other features include integrated pilot pressure and pressure gauge connections as well as being able to centrally regulate several gas supplies to the same working pressure, while the compact design enables them be installed in confined spaces. The maximum pre-pressure for the 737LE-HD is 240 bar with a regulating range from 2-45 bar.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa...
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin...
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more