Jena Tec Offers Ballscrew Repair Discount

Jena Tec can repair ballscrews of any make, type or configuration, with whichever type of ballscrew transfer system. Its specialised repair and ballscrew testing facilities means it repair ballscrews up to 15m in length and 200mm in diameter. The company can offer express ballscrew repair out of hours while the customer waits. It can collect failed ballscrews needing repair or be available to accept delivery 24/7.

Upon receipt of the ballscrew, it is logged onto the repair system and given a free assessment report - measuring critical parameters and conducting a 32-point ballscrew repair check. Jena Tec's ballscrew repair service technicians can assist with removal and refitting of the ballscrew on request. The company also provides rapid reverse engineering and emergency replacement of failed ballscrews if repair is not possible.

The ballscrew upgrade service diagnoses failure modes and provides a drop-in replacement from the XLF series precision ballscrews. Jena Tec offers European, UK and US ballscrew repairs. It can also repair belt-driven linear actuators, gearboxes and lifting jacks.

The company's repair capabilities include hard chrome, re-grinding, reverse engineering and replacement engineering of spare parts within the ballscrew, actuator or gearbox range. Ballscrews and actuators makes and manufacturers that can be repaired include: THK, NSK, Steinmeyer, Mannesmann, Hiwin, PMI, ABBA, Comtop, 20th Century TCM, Blis, Berger, Bosch Rexroth, SKF, PSI, Saginaw, Nook, Rockford, Nachi, Thompson IBL, Star, Shuton, Iperanga, Korta, LSI, Barnes, American Ballscrew and Warner Electric.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more