New Measuring Heads for Linear and Rotary Applications



With the LIMES LI20 and LI50 Kübler is presenting a new generation of measuring heads in a particularly solid die-cast housing. Used in conjunction with its magnetic bands with their stainless-steel covering, the resulting linear measurement system stays sealed even in harsh industrial environments and offers security against failures in the field. The magnetic rings offer the user a remarkably compact measurement system for rotary applications where installation space is very tight. Installation depths of only 16mm are possible with a large hollow shaft of 30mm. The combination of rings and bands plus Kübler's flexible manufacturing facilities open up a wide spectrum of different geometries that can be scanned, such as for example pitch circles or curves.

The non-contact technology ensures high vibration and shock resistance. The products can also be used outdoors, thanks to the high IP67 protection rating, the permitted 100% humidity with condensation, the wide temperature range and the weatherproof die-cast housing. The metal housing also offers improved shielding against electromagnetic interference.

Installation can be carried out very easily due to the large permitted tolerances of up to 1mm, which apply not only to the distance from band to sensor head but also for lateral misalignment, as well as to the built-in LED, which gives a red warning signal if the distance from the band to the reading head is too great or if the speed is too high. A green light shows the index pulse. The wide supply voltage range from 4.8 to 30 VDC likewise facilitates installation. The connections are made via a high-grade shielded PUR cable that is also suitable for trailing cable applications.

The sensing head is available either with a push-pull output or an RS422 interface and supplies two channels plus a periodic index with the corresponding inverted channels. The resolution is up to 5 mm with quadruple evaluation and the repeat accuracy is +/- one increment. The maximum traversing speed is 25m/s.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more