More Powerful, Versatile Preset Counters with up to 6 Presets and 4 Different Displays



The CODIX 92X are multitalented products that can handle the display, measurement and control of pulses (counter), frequencies (tacho) and time (timer), using numerous count functions and modes.
They thus offer a simple, cost-effective solution for many local standard control functions. When it comes to simple tasks, the many logic functions and preconfigured control functions offered by the CODIX 92X make them a real alternative to a PLC.

They can also be used as batch counters for controlling lot sizes, as a function of individual quantities, or as totalising counters for process control, as a function of the total count. In an additional role, they offer secure monitoring of time, frequency, position and pulses.

The CODIX 92X rangecomes equipped to meet the requirements of the user but can also be customised to his individual needs. Up to 10 inputs, up to 6 optocoupler outputs and up to 4 relay outputs are possible. In addition, versions with an RS 232/485 interface can be supplied.
It is not necessary to have in-depth programming knowledge when installing or using these devices, eliminating the need for costly service engineers. With all count functions there is direct access to the programming mode. On top of everything, the units are really easy to operate thanks to the simple, easy-to-understand programming structure and the alpha-numeric display of the parameters.  The various functions can be programmed either absolute or as tracking presets via the direct preset entry.
The counters boast a Teach-In function for error-free preset entry, a frequency display with fast display refresh and high accuracy (High Accuracy System), as well as many other count modes and functions.

The devices come factory-equipped with three predefined settings for the most common applications. If a parameter is modified, then the devices adopt the new function almost immediately: the programming is concluded in no time by means of the reset key. The functions Display Hold, Set and Teach-In can be called up via the new MPI input (Multiple Purpose Input).

Plug-in screw connectors with cage clamp terminals offer convenient time-saving installation. The front bezel is IP 65 sealed as standard, saving on additional time and effort for protecting the device during installation. And, of course, there will always be room for the Codix92X devices, thanks to their minimal installation depth.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more