Airchannel Helps With R-22 Refrigerant Phase Out

Airchannel is helping companies comply with legislation that phases out and removes the refrigerant R-22 from their compressed-air systems. Under EU Ozone Regulation EC2037/2000, the use of virgin R-22 refrigerant will be banned from the end of this year, as it contains ozone-depleting hydrochlorofluorocarbons (HCFCs). R-22 is used in a range of industries.

From January 2010 to January 2015, recycled HCFCs will be permitted but it is expected that supplies will be limited. For companies using R-22 within their compressed-air system, this could result in a significant operational headache. The likelihood of compressed-air systems using R-22 as a coolant increases significantly for equipment that is more than 10 years old. However, the legislation also represents an opportunity to help resolve two major issues facing industry - the rising cost of energy and environmental compliance.

Andrew Barraclough, national sales manager for Airchannel, said: 'R-22 will be totally phased out from the start of 2015 and relying on recycled HCFC is a risky strategy. 'To minimise the impact on their organisation, both operationally and financially, companies should address the issue as a priority. 'Essentially businesses have three choices. 'If it fits into the legislative timetable, they can run their chilling equipment to the end of its life and then install new technology.

'The alternatives are to remove the R-22 refrigerant and replace it with another compound that is suitable for their current systems and that complies with the legislation, or outright new equipment.' Airchannel has the expertise to make the required changes or advise if new equipment will be needed to comply with the legislation. It has worked with several customers in earlier gas-removal programmes and is now bringing its up-to-date knowledge of legislation and technical solutions to bear on the issue of R-22.

A number of new products have been put forward as potential replacements for R-22, although some require greater pressures that would have major implications for system components and current system designs. With higher-pressure gases there are several potential problems, such as whether the system can sustain the new pressure, requirements for all-new control switches and difficulty of oil changes inside the refrigerant. As a result this may not be a viable option on the grounds of cost.

However, Barraclough believes the phase-out of R-22 should be viewed as an opportunity that will ultimately offer operational efficiency and has the potential to reduce day-to-day energy costs. He added: 'Some companies are using the R-22 issue as an opportunity to review their entire systems, which has become even more important with the recent increases in energy prices.

'Airchannel has looked to improve efficiency and provide overall savings benefits through updating systems, advising of changes in operational practice or, as a last resort, replacement equipment. 'It is very easy for businesses to take their systems for granted. 'But this is an issue that has a deadline and needs addressing to ensure the appropriate action can be taken in time.' Any company in doubt as to the coolant used in its compressed-air system should contact an independent expert to arrange for an assessment as soon as possible.

Comments

Post a Comment

Popular posts from this blog

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more