The Interference Contour-Optimized LOG from SCHUNK is The Lightest and Lowest Priced Hole Gripper on The Market

SCHUNK, the competence leader for clamping technology and gripping systems, is considered the pioneer with respect to laser-sintered modules for handling applications. With a hole gripper made of chemical-resistant polyamide, the innovative family-owned company is now setting another new standard: The LOG is the lightest and also most low-priced hole gripper on the market. Compared with conventional rubber hole grippers, it is approximately 60% lighter. It also features high holding forces and increased durability. The generative manufacturing process used for the gripper allows extremely short delivery times even for individual shapes and sizes. Contrary to the widespread opinion that grippers made of plastic wear out quickly, the polyamide modules from SCHUNK prove to be extremely robust and abrasion-resistant. They are manufactured from lightweight and wear-resistant polyamide PA12 on modern laser sintering systems, directly from CAD data in a non-cutting process without tools. This enables complex contours or individual labeling at no additional cost.

The production technology used for the LOG results in a double advantage: they are resistant to dirt and also extremely lightweight. The gripper, which is comparable to a mandrel, features a one-piece design and a closed, and therefore completely dirt-resistant membrane system. Also, an internal stop protects the single-acting expansion membrane against damage. When compressed air is applied to the gripper via the outer or inner thread, the membrane expands and acts on the clamping jaws. The frictional engagement holds the workpiece securely. Due to the large-surface contact of the polyamide jaws on the wall, damage to the workpiece is more or less impossible - ideal prerequisites for handling of sensitive parts, such as sand cores, for example. When the air pressure is reduced, the membrane automatically returns to the starting position and the gripper jaw releases the part. The low material density makes SCHUNK hole grippers extremely lightweight. Use of the grippers increases the energy efficiency of handling systems. Alternatively, shorter cycle times or smaller systems can be achieved. LOG hole grippers are standardized for diameters between 20 and 40 mm. They weigh between 10 and 135 g and are designed for payloads between 1 and 4 kg. The grippers are driven by compressed air at 6 bar. Intermediate sizes and special shapes are possible on request. The interference contour-optimized grippers are equipped with connection threads for fast and easy mounting without tools.

The LOG from SCHUNK is a further addition to the company's line of laser sintered gripper modules. These modules include grippers with a closed drive membrane for hygiene-critical applications, individually formed and on request also flexible fingers, laser-formed quick-change systems that can be directly integrated in grippers or gripper fingers and, on request, can even be equipped with media feed-throughs. Since modules that have already been designed can be reproduced within a few days, the process is also ideal for wear and spare parts. SCHUNK is one of the first suppliers, who offers both fingers and quick-change systems and design services at flat rates. This means that the customer knows the exact costs in advance.

Comments

Post a Comment

Popular posts from this blog

FUSE SIZING CONSIDERATIONS FOR HIGHER EFFICIENCY MOTORS

Image
When selecting the proper fuse for short circuit protection in motor starting applications, it is important to not only ensure that the fuse will not nuisance open during motor start up times, but also that the fuse will coordinate as required with overload relays. When sizing fuses between 125% and 150% of the motor nameplate current, several advantages, including ease of coordination with an overload device, a smaller disconnect, and increased short circuit protection from a lower fuse rating, can be achieved. However, if sizing at this level prevents the motor from starting, it may then be necessary to increase the fuse ampere rating and it then becomes important to know the NEC sizing limitations. As of June 1, 2016, the US Department of Energy has mandated that newly manufactured electric motors will need to meet NEMA Premium® efficiency standards. As motor efficiencies increase, motor locked rotor currents can also be expected to increase. In addition to this, with across-the-lin
Read more

What is Class I Division 2?

Image
A Class I Division 2 is a location: (1) In which volatile flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are handled, processed, or used, but in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems from which they can escape only in case of accidental rupture or breakdown of such containers or systems or in case of abnormal operation of equipment, or (2) In which ignitable concentrations of flammable gases, flammable liquid-produced vapors, or combustible liquid-produced vapors are normally prevented by positive mechanical ventilation, and which might become hazardous through failure or abnormal operation of the ventilating equipment. Class I Division 2 Classification Class I Division 2 refers to the ANSI/ISA 12.12.01 standard. This standard was previously UL1604 until UL recommended the newer ANSI/ISA standard be used and that all hazardous location products be certified under this standa
Read more

7/8 16UN Connectors that Provide 600 Volts and 15 Amps

TURCK announces new A-Size 3 and 4-pin 7/8 16UN powerfast™ connectors that provide up to 600 Volts and 15 Amps of power. These IP67 rated connectors provide a modular wiring system designed to handle high current applications for machine power distribution, while providing resistance to vibration commonly associated with conveyors, motors and material handling applications. The cordsets are available with a tray rated, exposed run PVC flexlife ® cable, with or without STOOW rating, and 14 AWG wires that allow you to replace hard wiring with a robust, quick disconnect system that saves the time and money spent installing a conduit system. The A-Size powerfast line offers male and female, straight connectors, standard and custom lengths, and pigtails or extensions. To make the system complete, fully encapsulated mating receptacles, with 1/2”-14 NPT mounting threads are available.
Read more